Ball Bearing Gas Turbine Flow meters with Male NPT Fittings

FTB-930

Gas Turbine meters

PASSEZ VOTRE COMMANDE

Gas turbine meter with ±1% of Reading Accuracy
Ball Bearing Design for Economy
440C Bearing Retainers for Durability
Ball Bearings Field Replaceable Without Loss of Calibration
Deflector Cones Stabilize Low Mass Rotor for Increased Bearing Life
NIST Certificate Supplied Standard

Débitmètres à turbines/roues à aubes - Voir Les Produits Associés

Déscription

Click on this link if you need more information about a Flow meter.

The OMEGA™ turbine gas meter of the FTB-930 & FTB-940 have male NPT end fittings for easy connections. They are suitable for use with gases with a minimum density of 0.025 lb/ft 3 (air at STP is 0.0752 lb/ft 3 ).These units come supplied with a mating 2-wire connector and can be supplied with integrally mounted FLSC-60 Series signal conditioners to provide 4-20 mA, 0-5 V, or amplified pulse outputs. These turbine gas meters are intended for clean service only; where there is any doubt about the fluid, strainers are recommended.

OMEGA™ precision turbine gas flowmeters are designed to measure actual cubic feet or actual volume passing through the meter. Before sizing a flowmeter, it is necessary to convert flow units (i.e., SCFM, LPM, etc.) to actual units. To convert to actual measured volume (ACFM) from standard volume (SCFM), use the following formula:

ACFM	=	SCFM x 14.7/Pa x Ta/530
where:
ACFM	=	Actual cubic feet per minute of measured gas flow
SCFM	=	Standard cubic feet per minute gas flow
Pa	=	Operating pressure (psia) in = (psig + 14.7)
Ta	=	Temperature in degrees, Rankine = (°F + 460)

SPECIFICATIONS
Accuracy: ±1.0% of reading
Repeatability: ±0.25%
Materials of Construction:
Body: 304/316 stainless steel
Rotor: 17-4 PH SS
Bearings: 440C stainless steel
Output: 30 mV p-p sinewave min.

Placez votre commande(Veuillez spécifier la référence du produit)

Code d'article/ Desc.

Qté

Déscription

FTB-942

Consultez le Service de ventes

Stock:

75-1200 Max Linear Range (ACFM); 4 End Connections MNPT (in)

Accessories

PSU-24V-UNIVERSAL

Consultez le Service de ventes

Stock:

24V 0.75A regulated dc Power supply. 90-260 Vac 1.8 m lead with stripped ends. With International plugs

DPF20-HV-R1-R1

€327.30

Stock: 8 semaines

6 digit, 1/8 DIN panel meter for Rate or Total, 85 to 260 Vac powered, with dual relay outputs

† Tous les Montants indiqués Dans EUR
Notez: Comes complete with operator’s manual and NIST Certificate for air.

To order turbine gas meters with integral signal conditioners, specify model as a system such as : SYS/FTB-932/FLSC-62A. Omega will scale the signal conditioner with the appropriate calibration information from the turbine meter specified.

No other calibrations are available.

Compatible Meters: DPF701, DPF402, DPF70 with FLSC-AMP, DPF10, DPF500, FC20, 21, 22

Contact Flow Engineering Dept

Exemple de commande: (1) DPF702 1/8 DIN Panel Meter for Rate or Total, €340.21

Manuels de Produit:

Télécharger FTB-900/FTB9500 Series - Precision Turbine Flowmeters

Télécharger FLSC-64 - Pulse Amplifier

Télécharger FLSC-62A - Signal Conditioner

Télécharger FLSC-61 - 3-Wire Analog Transmitter

Produits Liés:

FLSC-60
Achetez maintenant →
Direct Mounting Signal Conditioners for FTB-900, FTB-930,FTB-9500, FTB-950 and FTB-970/980 Series Turbine Flowmeters

DPF700 Series
Achetez maintenant →
Discontinued - Six Digit Ratemeter or Totaliser.