Cookies sur les sites Web Omega
Nous utilisons des cookies sur ce site Web. Ces cookies sont indispensables au bon fonctionnement de notre site.
Si vous continuez sans modifier vos paramètres, nous supposerons que vous êtes heureux de recevoir tous les cookies de notre site Web.
Pour de plus amples informations à ce sujet, veuillez cliquer ici
Fermer
Panier  |  Contact  | 
NUMÉRO VERT 0805 541 038
INTERNATIONAL+33 01 57 32 48 17
Layer N Banner

Strain Gauge Adhesive Kit

Strain Gage and Transducer Accessories

Strain Gauge Adhesive Kit | Strain Gage and Transducer  Accessories

Strain Gauge Adhesive Kit

  • Bridge Completion Resistors
  • Strain Gage Adhesives
  • Resistance Wire for Temperature Compensation and Zero Balance
Jauges de contrainte, accessoires et instrumentation - Voir Les Produits Associés

Déscription

TERMINAL PADS
Terminal pads serve two main purposes. First, they act as intermediate points for attaching ribbon leads of thin gage wire to heavier instrumentation wires. Second, they provide stress relief to strain gage systems. When the heavy instrumentation wire moves, the terminal pad protects the strain gage.

FIXED BRIDGE COMPLETION RESISTORS
Accuracy:0.1%
Temperature Compensation: 5 ppm (-20 to 80°C/-4 to 176°F)
Power: 1 /4 watt.

ADHESIVES
OMEGA’s TT300 cement is a heat-cured, two-part epoxy adhesive which can be used to bond polyimide backed strain gages for strain measurement up to 200°C (392°F). Each TT300 kit contains 2 bottles of resin and hardener which are premeasured to insure proper mixing proportions. To use, simply pour one bottle of hardener into one bottle of resin and shake for one minute. A bottle each of hardener and resin produce approximately 3 /4 oz. of adhesive. The shelf life of the resin-hardener mixture is six weeks at room temperature. The shelf life of the unmixed components is indefinite, provided the bottles are kept tightly sealed. Each TT300 kit includes 2 oz. of Acetone, Acid Primer, Neutralizer and Rosin Solvent for cleaning and preparing the surface, as well as two funnels and two cap brushes. SG496 and SG401 are general purpose cold-curing one-part glues. They are the easiest and most commonly used adhesive for strain gages. They cure in one minute, but require 24 hours to set. SG401 is an ethyl-based cyanoacrylate and SG496 is a methyl-based cyanoacrylate. There is a one-year shelf life at cool room temperature, but increased shelf life can be obtained by cold storage. The glue temperature range is -65 to 180°F (-54 to 82°C).

NOTE: Additional Hazardous Materials carrier handling surcharges may apply for adhesive products on this page. You will be contacted by Internet Sales to confirm after the order is placed.
Placez votre commande(Veuillez spécifier la référence du produit)
Code d'article/ Desc.
Qté
Déscription
TP-1
Consultez le Service de ventes  
Stock: 
 
 
single terminal pad pair, pkg of 10
TP-2
Consultez le Service de ventes  
Stock: 
 
 
two terminal pad pairs, pkg of 10
TP-3
Consultez le Service de ventes  
Stock: 
 
 
three terminal pad pairs, pkg of 10
TP-4
Consultez le Service de ventes  
Stock: 
 
 
four terminal pad pairs, pkg of 10
TP-5
Consultez le Service de ventes  
Stock: 
 
 
five terminal pad pairs, pkg of 10
TP-6
Consultez le Service de ventes  
Stock: 
 
 
six terminal pad pairs, pkg of 10
RES-120
16.94
Stock: 1 semaine
 
120 Ohm bridge completion resistors
RES-250
16.67
Stock: 1 semaine
 
250 Ohm bridge completion/4-20 mA shunt resistors
RES-350
17.89
Stock: 1 semaine
 
350 Ohm bridge completion resistors
TT300
Consultez le Service de ventes  
Stock: 
 
 
Adhesives
SG496
42.65
Stock: 1 semaine
 
1 oz. ethyl-based cyanoacrylate adhesive (bonds approx. 50 gages)
SG401
13.43
Stock: En stock
 
0.1 oz. ethyl-based cyanoacrylate adhesive (bonds approx. 50 gages)
SGB-36
109.78
Stock: 7 semaines
 
36 gage Balco wire (500 ft) for zero and span temperature compensation, 19.7 Ohms/ft, temp. coefficient 0.45%/°C
SGC-36
Consultez le Service de ventes  
Stock: 
 
 
36 gage Copper wire (1500 ft) for zero and span temperature compensation, 0.415 Ohms/ft, temp. coefficient 0.39%/°C
SGM-36
38.04
Stock: 9 semaines
 
36 gage Manganin wire (200 ft) for zero balance, 15.2 Ohms/ft, temp. coefficient 0.002%/°C
Tous les Montants indiqués Dans EUR
Notez: TT300 KIT INCLUDES:
(2) 1 oz. resin bottles ( 1 /2 filled)
(2) 1 oz. hardener bottles ( 1 /2 filled)
(2) plastic funnels (35 mm diameter)
(2) brush caps
(1) 2 oz. bottle of acetone
(1) 2 oz. bottle of acid primer
(1) 2 oz. bottle of neutralizer
(1) 2 oz. bottle of resin solvent
(1) manual

Manuels de Produit:

Télécharger TT300 Series - Adhesive Kit
Télécharger SG401 and SG496 - Rapid Cure Strain Gauge Adhesives
We noticed you are from the US. Visit your local site for regional offers and live support.