Cookies sur les sites Web Omega
Nous utilisons des cookies sur ce site Web. Ces cookies sont indispensables au bon fonctionnement de notre site.
Si vous continuez sans modifier vos paramètres, nous supposerons que vous êtes heureux de recevoir tous les cookies de notre site Web.
Pour de plus amples informations à ce sujet, veuillez cliquer ici
Fermer
Panier  |  Contact  | 
NUMÉRO VERT 0805 541 038
INTERNATIONAL+33 01 57 32 48 17
Layer N Banner

Terminal Covers, Clamping Bands and Insulators

STRIP Heater Accessories

Terminal Covers, Clamping Bands and Insulators | STRIP Heater Accessories

Terminal Covers, Clamping Bands and Insulators

35,47 PCN255716

Déscription

Secondary Insulation Bushing: All types except NS. Must be used when strips are mounted for air heating only or when connected in series on line voltages above 480V. Note: To accommodate bushings, a 17 /32 " x 11 /16 " dia. mounting hole in tabs should be specified for heaters.

Strip Element Clamps: Cast-iron clamps for use with OMEGALUX ® strip elements, retain their strength at elevated temperatures to assure maximum sheath-to-surface contact. Resulting uniform efficient heat transfer from internal resistance wire to the heated material avoids hot spots on the element, contributing to long service life.

Type SC Clamping Bands: A permanently tight fit on cylinders, nozzles, pipes and other round surfaces is provided by the Type SC stainless steel band with alloy screw. For small pipe diameters, strip elements should have cross-section curving (contact OMEGALUX). For most satisfactory results, bands should be spaced about 5 inches apart and should be drawn up tight to assure good contact between heater or thermostat bulb and surface. Installation: Fasten studs to the work surface by welding, brazing or threading. Use correct size stud to fit clamp. (See sketches to left). For temperatures over 750°F, stainless steel studs are recommended. When tightening nuts, torsion should not exceed 10 foot pounds maximum. Heaters must be allowed to expand. One clamp should hold heater. Nuts on other clamp should be backed off approx. 1 /2 turn to allow heaters to expand.
Placez votre commande(Veuillez spécifier la référence du produit)

Ce que d'autres personnes ont acheté: quand vous voyez cette icône, cliquez dessus pour afficher une liste des produits que d'autres personnes ont achetés en plus de ce modèle.

Code d'article/ Desc.
Qté
Déscription
Terminal Covers and Insulator
Cliquez pour agrandir / réduire une liste d'achat connexePCN255716
PCN255716
35.47
Stock: 1 semaine
 
Secondary insulation bushing
Cliquez pour agrandir / réduire une liste d'achat connexeH-TP
H-TP
33.59
Stock: 7 semaines
 
Ceramic post terminal insulators
Cliquez pour agrandir / réduire une liste d'achat connexeOT-AC-1
OT-AC-1
48.17
Stock: 5 semaines
 
Terminal cover for OT series strip heaters
  
PT-AC-1
44.62
Stock: 5 semaines
 
Terminal cover for PT series strip heaters
  
SE-AC-1
43.62
Stock: 1 semaine
 
Terminal cover for SE series strip heaters
Clamping Devices
  
SC-820-20
Consultez le Service de ventes  
Stock: 
 
 
Clamping band
  
SC-820-30
Consultez le Service de ventes  
Stock: 
 
 
Clamping band
  
SC-820-34
Consultez le Service de ventes  
Stock: 
 
 
Clamping band
  
SC-820-40
Consultez le Service de ventes  
Stock: 
 
 
Clamping band
  
SC-820-46
Consultez le Service de ventes  
Stock: 
 
 
Clamping band
Tous les Montants indiqués Dans EUR
We noticed you are from the US. Visit your local site for regional offers and live support.