Cookies sur les sites Web Omega
Nous utilisons des cookies sur ce site Web. Ces cookies sont indispensables au bon fonctionnement de notre site.
Si vous continuez sans modifier vos paramètres, nous supposerons que vous êtes heureux de recevoir tous les cookies de notre site Web.
Pour de plus amples informations à ce sujet, veuillez cliquer ici
Fermer
Panier  |  Contact  | 
NUMÉRO VERT 0805 541 038
INTERNATIONAL+33 01 57 32 48 17
Layer N Banner

Programmable Stepper Drive with Integrated Power Supply

Si3540

Programmable Stepper Drive | Si3540

Programmable Stepper Drive

Garantie 1 an CE
  • 3.5 A, 40 Vdc
  • 110/220 Vac Input, 50/60 Hz Switch Selectable
  • Microstepping 2000 to 50,800 Steps/Rev
  • Idle Current Reduction Software Selectable: 0, 25, 50, or 100%
  • Software Selectable Motor Current 0.2 to 3.5 A/Phase
  • Eight Optically Isolated Inputs 5 to 24 Vdc
  • Three Optically Isolated Outputs 12 to 24 Vdc, 100 mA max
  • One Optically Isolated Output 5V, Dedicated to Fault Out
  • Download, Store and Execute Programs Using Si Programmer (Free Download)
  • Mating Connectors Included
  • Sample Motion Programs Available by Request
Variateurs et moteurs - Voir Les Produits Associés

Déscription

The Si3540 is a programmable step motor drive/indexer packaged in a rugged steel and aluminum enclosure. Integral power supply, heat sink, mounting brackets, switch covers and connectors are included with each Si3540. The Si3540 comes with all operating software necessary to create a complete step motor-based motion control solution.

The Si3540 includes Applied Motion Products' Windows-based Si Programmer™ software application for quick set up and ease of use. Si Programmer™ is ideal for stand-alone operation. For users with software development expertise, the Si3540 can also be used with Applied Motion's Si™ Command Language (SCL). SCL allows for control of an Si drive, like the Si3540, via serial commands sent from a host device such as a PC or PLC. This permits the user to perform a variety of motion, I/O, and system status tasks via a host serial device.

Multiple axis applications can be handled with the SiNet™ Hub Programmer software, which gives you the ability to control up to 4 "Si" or "i" drives, stepper and servo, from just one SiNet™ Hub 444. Not only can you sequence up to four motors, but a SiNet™ Hub 444 also has access to the inputs and outputs of all the drives connected to it, providing your program with up to 32 inputs and 12 outputs. In addition, the Hub 444 provides 4 digital inputs and 4 digital outputs of its own. You can also use Applied Motion's MMI-01 to interface the drives with the machine operator.

Factory set to operate at 110 VAC input, the Si3540 can be set by the user to operate at 220 VAC input by a simple switch selection.

Pluggable screw terminal blocks are provided for the I/O, motor, and AC power input. Mating connectors, programming cable with computer interface connector, as well as all operating software are provided with each Si3540 drive.

The Si3540 is both CE and TUV compliant.

Si Programmer
Intended for use in stand-alone applications, Si (Simple Indexer) Programmer provides quick, out-of-the-box use with an extremely friendly, point-and-click graphical interface that does not require any software programming experience. Once an Si program has been constructed and downloaded to the drive, the program can be executed stand-alone at power-up or from an external trigger. Constructing a program is accomplished through the use of instructions selected in a point-and-click manner. Once an instruction is selected, a "fill in the blanks" format is used to input parameters.

Constructing an Si program requires no prior programming experience nor does it require learning a programming language. Si Programmer generates the actual motion control program, based on user selected parameters, thereby eliminating syntax errors. Once created, programs are easily downloaded, uploaded, saved and printed.

Si Programmer also provides the capability to control digital inputs and outputs, useful for interfacing with external equipment like PLCs, sensors, end-of-travel switches, and more. Si Programmer has found success in all types of applications, from simple linear actuator applications to complete machine control with operator interface applications.

NOTE:   Power cord not included. See Accessories below to order.
Placez votre commande(Veuillez spécifier la référence du produit)

Ce que d'autres personnes ont acheté: quand vous voyez cette icône, cliquez dessus pour afficher une liste des produits que d'autres personnes ont achetés en plus de ce modèle.

Code d'article/ Desc.
Qté
Déscription
Accessories
  
MMI-01
Consultez le Service de ventes  
Stock: 
 
 
Operator Interface
Cliquez pour agrandir / réduire une liste d'achat connexeOM-CONV-USB
OM-CONV-USB
€23.30
Stock: 1 semaine
 
USB to RS232 Interface Converter; USB-A to DB9-male
  
Power Cord-SE
€12.18
Stock: 4 semaines
 
AC Power cord with stripped end termination
  
Power Cord-SE-M16
€17.27
Stock: 1 semaine
 
8' Power cord with M16 cable gland strain relief, 3x16 AWG, 250Vac max.
  
SI-PROG-CBL
€31.57
Stock: 1 semaine
 
Replacement programming cable (comes with drive)
  
DSUB-9-MF
Consultez le Service de ventes  
Stock: 
 
 
DIN rail interface module, 9-pin
  
DSUB-9-MF-CBL
€48.42
Stock: 1 semaine
 
DSUB cable, 9-pin, 2 m (6.6'), male/female connectors
Tous les Montants indiqués Dans EUR
Notez: Programming cable and mating connectors are included. Programming software is a free download; click on "Software" icon below the picture. To see torque-speed curves for recommended motors, click on "Specs" above.
We noticed you are from the US. Visit your local site for regional offers and live support.